Make sure to use safety precautions while using heat. Using heat makes the process much easier than if you tried to accomplish it without and also saves your paint from unnecessary roughness. If it’s a cloudy day or in the middle of winter, it’s not a problem, just get out a heat gun or the family hair dryer and blast some heat onto the affected area with the pinstripes. If you decide to do this project on a summer day, then this is easy for you! Park your car out in direct sunlight for about 30 minutes before you start the removal job. Heat Source – You will need a heat source to soften up the vinyl in order to make it easier to remove and more time effective.That’s 85 pages of tips and tricks about auto body and what you could do to restore your car. If you’re into body and paint and you want to learn further how to customize your cars, put body kits, do body work, restore your classic – check out our VIP Course right now! I’m giving away a FREE 85-Page Auto Body And Paint Manual where you can basically download it. I just thought of doing mine like I did because the body line is gone when you get to the fender, that’s why I decided to do a design that ended about five inches into the fender area. It’s all up to you whatever design you want to do on the front. It just gives it a different kind of look. It came out looking really cool! It gave the car a nice custom look for about 15 minutes of work. I hope you like the quick little tutorial on putting pinstripe on the side of the car. Just use the same razorblade to cut the extra pinstripe lines on the designs like I did on both ends. We just removed the thicker line since we don’t need it. I added some red inside the black one, just using the skinny/thin line of the red pinstripe to put in between the black thick and thin lines in order to add more color and design to it. I used 2-tone pinstriping on the front end. I am obsessed about making it look identical while just eyeball-measuring the lines. The challenging part is working on two opposite sides and having to go back and forth copying what you’ve done on the finished side and making sure it looks the same. Just press the ends to secure it in place. It was the same for the front end, just came up with a different design just to make it look more interesting. You can use the same razorblade to cut the pinstripe connecting the door panels. Don’t push too hard when you’re doing this, instead just do it very lightly and cut the extra pinstripe to achieve your desired design. Took about an inch from the end of the sticker and formed the exact design I had on the finished side, using a sharp razor blade. While doing that, I make sure that the sticker was pressed well. I just use my fingers, hands to measure the distances and sizes.Īfter that, I peeedl off the plastic covering that’s on the pinstripe. I saw the design of the back window where the moldings formed kind like of a triangle shape so I thought of copying that, then did the same on the side I was working on in the video. I also did some designs on the front and back ends of the pinstripe. I started at the back panel which is narrower and it got wider towards the front part. So I just really followed the body line as you can see in the video. I had to redo the front section because it wasn’t looking too straight. If you do it abruptly and too hard, it might cause an overlap and you don’t want that. When you’re pushing or sealing the pinstripe, just do it lightly at first. You don’t want any spots where the pinstripe is thinner than the rest. You also don’t want to pull too tight because you’ll stretch it and it will make it thinner. Of course, you can always peel it off and redo. I’m holding the pinstripe in a certain way so that as I peel, I’m peeling the back off the pinstripe. Make sure to press on the end of every panel, that way if you have to peel the beginning end to redo it because it’s not straight enough or whatever, at least it doesn’t peel off the whole thing.Īfter you’re done with the first area, just keep on doing it on the next areas. Make sure you watch the video so you can see how I do it. Once you get started, you go over the body line. I chose the thick stripe on top.īefore you start putting the pinstripe, make sure your body panel is clean – wash the car, the area and dry with a shammy. Like in the pinstripe I used, you can choose to have it thick stripe on top or thin stripe on top. Then, you can figure out how you want it to look. So what you do is, first see how much you need. You don’t have to have a lot of skills like those painting pinstriping that other guys do. I was doing the design on the sides of a 2015 Isuzu Highlander, just to give it some pizzazz. In this quick video, I’ll show you how to pinstripe your car with vinyl striping.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |